BJJFQ - STARTING FLUID CYLINDER
- MSDS: BJJFQ
- Manufacturer: KBI KOLD BAN INTERNATIONAL LTD
- Product Name: STARTING FLUID CYLINDER
- National Stock Number: 2910-00-646-9727
Product Identification
Product ID:STARTING FLUID CYLINDER
MSDS Date:12/08/1989
FSC:2910
NIIN:00-646-9727
MSDS Number: BJJFQ
Responsible Party
LAKE IN THE HILLS, IL 60102-9637
US
Info Phone: 708-658-8561
Cage: 53203
Contractor
Telephone: 708-658-8561
Cage: 53203
Ingredients
CARBON DIOXIDE
CAS: 124-38-9
RTECS: FF6400000
OSHA PEL 5000 PPM
ACGIH TLV: 5000PPM/30000STEL;93
ETHYL ETHER (SARA III)
CAS: 60-29-7
RTECS: KI5775000
OSHA PEL 400 PPM/500 STEL
ACGIH TLV: 400PPM/500STEL; 9192
EPA Report Quantity: 100 LBS
DOT Report Quantity: 100 LBS
N-HEPTANE
CAS: 142-82-5
RTECS: MI7700000
OSHA PEL 500 PPM/500 STEL
ACGIH TLV: 400 PPM/500STEL;9293
MINERAL OIL, SEVERELY HYDROTREATED, PREDOMINATELY
CAS: 64742-53-6
RTECS: PY8036000
OSHA PEL 5 MG/M3 (OIL MIST)
ACGIH TLV: 5 MG/M3 (OIL MIST)
Hazards
LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:SEE SIGNS & SYMPTOMS OF OVEREXPOSURE
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:INHAL: DIZZINESS, STRONG ANESTHESIA,
INTOXICATION, UNCONSCIOUNESS. SKIN: IRRITATION UPON PROLONGED
CONTACT, DEFATTING OF SKIN. EYE: IRRITATION.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.
First Aid
First Aid:INHAL: REMOVE TO FRESH AIR. ARTIFICIAL RESPIRATION. GET MD
IMMED. SKIN: FLUSH AREA WELL WITH WATER. REMOVE & WASH ANY CLOTHING
SOAKED WITH PRODUCT. EYE: FLUSH WELL WITH RUNNING WATER FOR 15
MINUTES. I NGEST: CALL MD OR POISON CONTROL IMMED.PROPER TREATMENT
IS DEPENDENT ON CONDITION OF PATIENT & AMOUNT INGESTED.
Fire Fighting
Flash Point Method:TCC
Flash Point:-56 F, (ING 2)
Lower Limits:1.8 (ETHER)
Upper Limits:48.0 (ETHER)
Extinguishing Media:DRY CHEMICAL, CARBON DIOXIDE, WATER FOG OR MIST
ONLY, ALCOHOL FOAM
Fire Fighting Procedures:AVOID POSSIBLE ACCUM OF FLAM VAPORS AT LOW
LVLS, AS VAPOR IS HVR/AIR. NIOSH/MSHA APPROVED SCBA & PROT CLOTHING
SHOULD BE WORN WHEN FIGHTING CHEM FIRES
Unusual Fire/Explosion Hazard:AVOID HAZARDOUS CONTAINER PRESSURES. DO
NOT STORE WHERE TEMPERATURE MAY EXCEED 120 F. DO NOT PUNCTURE OR
INCINERATE CONTAINER.
Accidental Release
Spill Release Procedures:KEEP AWAY FROM HEAT, FIRE, SPARKS, OR FLAME.
IF CONTENTS ARE RELEASED OR SPILLED, VENTILATE AREA WELL. CO*2 MAY
BE USED AS A PRECAUTIONARY VAPOR BLANKET. SMALL AMOUNTS MAY BE
FLUSHED AWAY WITH WATER.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
Handling
Handling and Storage Precautions:DO NOT STORE WHERE TEMPERATURE MAY
EXCEED 120 F. DO NOT STORE NEAR HEAT, FIRE, FLAME, OR SPARKS.
Other Precautions:READ ALL CAUTIONARY INFORMATION ON CYLINDERS. USE IN
ACCORDANCE WITH DIRECTIONS. DO NOT USE NEAR HEAT, FIRE, FLAME OR
SPARKS. DO NOT SPRAY IN DIRECTION OF BODY. USE ONLY WITH GOOD
VENTILATION. KEEP AW AY FROM CHILDREN.
Exposure Controls
Respiratory Protection:IF TLV IS EXCEEDED WEAR NIOSH/MSHA APPROVED SCBA
OR RESPIRATOR APPROPRIATE FOR EXPOSURE OF CONCERN.
Ventilation:MUST BE ADEQUATE TO MAINTAIN VAPORS AT LESS THAN 400 PPM,
PARTICULARLY AT FLOOR LEVEL (SEE SUPP DATA)
Protective Gloves:NITRILE OR OTHER IMPERVIOUS TYPE
Eye Protection:CHEMICAL WORKERS GOGGLES
Other Protective Equipment:AS REQUIRED TO AVOID CONTACT W/SKIN, EYES OR
CLOTHING. VAPORS MAY IRRITATE EYES.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
VENTILATION (CON'T): AS VAPORS ARE HEAVIER THAN AIR. AVOID EXCESSIVE
BREATHING OF VAPORS.
Chemical Properties
Boiling Pt:B.P. Text:94F (ING 2)
Vapor Pres:150 PSIG
Vapor Density:APPROX 2.5
Spec Gravity:0.70
Evaporation Rate & Reference: 7.0 (BUTYL ACETATE = 1)
Solubility in Water:APPROX 7% @ 70 F
Appearance and Odor:PALE YELLOW TO CLEAR LIQ, STRONG ETHEREAL ODOR,
EVAPS QUICKLY, LEAVES LUB RESID
Percent Volatiles by Volume:99
Stability
Stability Indicator/Materials to Avoid:YES
CONTENTS OF CYLS SHOULD NOT BE EXPOSED TO AIR & LIGHT. UNSTABLE
PEROXIDES MAY BE FORMED & CONCENTRATE BY EVAP TO HAZ LVL
Stability Condition to Avoid:HEAT, SPARKS, FLAMES, STRONG OXIDIZERS
Hazardous Decomposition Products:CARBON MONOXIDE MAY FORM ON COMBUSTION
Disposal
Waste Disposal Methods:DISPOSE OF CONTENTS PROMPTLY IN SEALED METAL
CONTAINERS, IN ACCORDANCE WITH ALL LOCAL, STATE & FEDERAL
REGULATIONS. AVOID ANY CONTAMINATION OF GROUND WATER. DO NOT
PUNCTURE OR INCINERATE CONTAINER.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.